Introduction

Arduino has popularized the concept of adding an abstraction layer over the MCU GPIOs and ADC multiplexer as "Digital Pins" and "Analog Pins". For historic reasons as well as to express appreciation for the introduction of concept, we prefix features and macros that map board pins to MCU pins with ARDUINO.

Note: This means, we also explicitly use the Arduino feature for boards that are neither official Arduino products nor compatible.

I/O Mappings

All I/O mappings are provided by the arduino_iomap.h header file. This is provided either by the board directly (e.g. in <RIOT git repo>/board/<board>/include/arduino_iomap.h) or by the board family (e.g. in board/common/<board family>/include/arduino_iomap.h).

To add support to new boards, start by copy-pasting the arduino_iomap.h from an existing board and adapt/extend the macros as needed. Finally, add the features to the Makefile.features and KConfig files of the board that indicate the presence of the added mappings.

Digital Pins

The feature arduino_pins is provided by boards that do have a mapping to digital pins. The GPIO for e.g. D3 is provided as ARDUINO_PIN_3. The number of the highest digital pin is provided as ARDUINO_PIN_LAST. E.g. if ARDUINO_PIN_LAST is 42, digital pins D0 to D42 are typically provided.

Warning: Some boards do have "gaps" in the pin mapping. It could be that e.g. ARDUINO_PIN_5 is defined, but ARDUINO_PIN_4 is not.

Note: Often aliases are provided for analog pins in digital mode. E.g. to use the pin A3 as digital pin, ARDUINO_PIN_A3 can be used to avoid looking up what digital number that pin has.

Analog Pins

The feature arduino_analog is provided by boards that do have a mapping of ADC lines to analog pins. E.g. the ADC line corresponding to pin A5 would be ARDUINO_A5. The number of the highest analog pin is provided as ARDUINO_ANALOG_PIN_LAST. The macro ARDUINO_ANALOG_PIN_LAST is defined if and only if a mapping is provided (so it can be used to test for this feature).

Warning: Some boards do have "gaps" in the analog pin mapping. It could be that e.g. ARDUINO_A3 is defined, but ARDUINO_A2 is not.

DAC Pins

The feature arduino_dac is provided by boards that do have a mapping of DAC pins to DAC lines. E.g. the DAC line for the pin DAC1 would be ARDUINO_DAC1. The number of the highest DAC pin is provided as ARDUINO_DAC_PIN_LAST. The macro ARDUINO_DAC_PIN_LAST is defined if and only if a mapping is provided (so it can be used to test for this feature).

Warning: Some boards do have "gaps" in the analog pin mapping. It could be that e.g. ARDUINO_DAC4 is defined, but ARDUINO_DAC3 is not.

PWM Pins

The feature arduino_pwm is provided by boards that do have a mapping of digital pins to PWM settings. E.g. the PWM device connected to the digital pin D11 would be ARDUINO_PIN_11_PWM_DEV and the channel would be ARDUINO_PIN_11_PWM_CHAN. A PWM frequency for all PWM pins is defined as ARDUINO_PWM_FREQU.

Warning: Typically only few digital pins support PWM. For pins without PWM output no ARDUINO_PIN_<NUM>_PWM_DEV macro and no ARDUINO_PIN_<NUM>_PWM_DEV is defined.

UART Device

The feature arduino_uart is provided by boards that do provide an UART device mapping. For the official Arduino boards and compatible boards, the ARDUINO_UART_D0D1 macro refers to the UART device that uses the digital pins D0 and D1.

Please extend the table below to keep naming among boards of the same form factor consistent:

Form Factor	Macro Name	Description
Arduino Nano	`ARDUINO_UART_D0D1`	UART on D0 (RXD) and D1 (TXD)
Arduino Uno	`ARDUINO_UART_D0D1`	UART on D0 (RXD) and D1 (TXD)
Arduino Mega	`ARDUINO_UART_D0D1`	UART on D0 (RXD) and D1 (TXD)

I²C Buses

The feature arduino_i2c is provided by boards that do provide an I²C bus mapping.

Form Factor	Macro Name	Description
Arduino Nano	`ARDUINO_I2C_NANO`	D18 (SDA) / D19 (SCL)
Arduino Uno	`ARDUINO_I2C_UNO`	D18 (SDA) / D19 (SCL)
Arduino Mega	`ARDUINO_I2C_UNO`	D20 (SDA) / D21 (SCL)
Arduino Zero	`ARDUINO_I2C_UNO`	D20 (SDA) / D21 (SCL)
Arduino Due	`ARDUINO_I2C_UNO`	D70 (SDA) / D71 (SCL)

The ARDUINO_I2C_UNO refers to the I²C bus next to the AREF pin (the topmost pins on header on the top right) of an Arduino Uno compatible board, e.g. such as the Arduino Mega2560. Even though the Arduino UNO, the Arduino MEGA2560, the Arduino Zero and the Arduino Zero all having the I²C bus at the exact same mechanical positions, the digital pin number of the I²C bus next to the AREF differs between the versions.

SPI Buses

The feature arduino_spi is provided by boards that do provide an SPI bus mapping.

Form Factor	Macro Name	Description
Arduino Nano	`ARDUINO_SPI_ISP`	The SPI on the ISP header
Arduino Nano	`ARDUINO_SPI_D11D12D13`	D11 (MOSI) / D12 (MISO) / D13 (SCK)
Arduino Uno	`ARDUINO_SPI_ISP`	The SPI on the ISP header
Arduino Uno	`ARDUINO_SPI_D11D12D13`	D11 (MOSI) / D12 (MISO) / D13 (SCK)
Arduino Mega	`ARDUINO_SPI_ISP`	The SPI on the ISP header
Arduino Mega	`ARDUINO_SPI_D11D12D13`	D11 (MOSI) / D12 (MISO) / D13 (SCK)

Note: The original AVR based Arduinos only have a single hard SPI bus which is only provided via the ISP header. Many modern Arduino compatible boards do not provide the ISP header and only have SPI on D11/D12/D13 provided.

Mechanical and Electrical Compatibility

Modules implementing drivers for extension boards, a.k.a. shields, can express their mechanical and electrical requirements by depending on arduino_shield_... features. The following list of features currently exists:

Note: A board providing arduino_shield_mega MUST also provide arduino_shield_uno, as Arduino MEGA boards are backward compatible to shields for the Arduino UNO.

E.g. a module that implements the W5100 based Ethernet shield would depend on both arduino_shield_uno and arduino_shield_isp for electrical compatibility as well as on arduino_spi for SPI bus mapping and arduino_pins for the CS pin mapping. This module could reuse the existing w5100 driver and just supply the correct w5100_params_t using the I/O mappings.