lm75_params.h

Go to the documentation of this file.

/*
 * SPDX-FileCopyrightText: 2021 ML!PA Consulting GmbH
 * SPDX-License-Identifier: LGPL-2.1-only
 */
 
#pragma once

 
#include "board.h" /* IWYU pragma: keep */
#include "lm75.h"
#include "lm75_regs.h"
#include "modules.h"
 
#ifdef __cplusplus
extern "C" {
#endif
 
#ifndef LM75_PARAM_I2C
#  define LM75_PARAM_I2C I2C_DEV(0) 
#endif

#ifndef CONFIG_LM75_I2C_ADDR
#  define CONFIG_LM75_I2C_ADDR (0x48)
#endif
 
/* Device operation mode configuration - normal or shutdown */
#if IS_ACTIVE(CONFIG_NORMAL_MODE)
#  define CONFIG_OPERATION_MODE NORMAL_MODE
#elif IS_ACTIVE(CONFIG_SHUTDOWN_MODE)
#  define CONFIG_OPERATION_MODE SHUTDOWN_MODE
#endif
 
#ifndef CONFIG_OPERATION_MODE
#  define CONFIG_OPERATION_MODE NORMAL_MODE 
#endif
 
/* Device Overtemperature Shutdown operation mode configuration - comparator or interrupt */
#if IS_ACTIVE(CONFIG_COMPARATOR_MODE)
#  define CONFIG_THERMOSTAT_MODE COMPARATOR_MODE
#elif IS_ACTIVE(CONFIG_INTERRUPT_MODE)
#  define CONFIG_THERMOSTAT_MODE INTERRUPT_MODE
#endif
 
#ifndef CONFIG_THERMOSTAT_MODE
#  define CONFIG_THERMOSTAT_MODE COMPARATOR_MODE 
 
#endif
 
/* Device Overtemperature Shutdown polarity configuration - OS active low or high */
#if IS_ACTIVE(CONFIG_OS_ACTIVE_LOW)
#  define CONFIG_OS_POLARITY OS_ACTIVE_LOW
#elif IS_ACTIVE(CONFIG_OS_ACTIVE_HIGH)
#  define CONFIG_OS_POLARITY OS_ACTIVE_HIGH
#endif
 
#ifndef CONFIG_OS_POLARITY
#  define CONFIG_OS_POLARITY OS_ACTIVE_LOW 
 
#endif
 
#if IS_ACTIVE(CONFIG_FAULT_1)
#  define CONFIG_FAULT_QUEUE FAULT_1
#elif IS_ACTIVE(CONFIG_FAULT_2)
#  define CONFIG_FAULT_QUEUE FAULT_2
#elif (IS_ACTIVE(CONFIG_FAULT_3) && IS_USED(MODULE_TMP1075))
#  define CONFIG_FAULT_QUEUE FAULT_3
#elif (IS_ACTIVE(CONFIG_FAULT_4) && IS_USED(MODULE_LM75A))
#  define CONFIG_FAULT_QUEUE FAULT_4
#elif (IS_ACTIVE(CONFIG_FAULT_4) && IS_USED(MODULE_TMP1075))
#  define CONFIG_FAULT_QUEUE FAULT_4_TMP1075
#elif (IS_ACTIVE(CONFIG_FAULT_6) && IS_USED(MODULE_LM75A))
#  define CONFIG_FAULT_QUEUE FAULT_6
#endif

#ifndef CONFIG_FAULT_QUEUE
#  define CONFIG_FAULT_QUEUE FAULT_1
#endif
 
#ifndef LM75_PARAM_INT
#  define LM75_PARAM_INT GPIO_UNDEF 
#endif
 
#define LM75A_CONV_RATE    (100)  
 
#define LM75A_OS_RES       (5)    
#define LM75A_OS_MULT      (10)   
#define LM75A_OS_SHIFT     (7)    
#define LM75A_TEMP_RES     (125)  
#define LM75A_TEMP_MULT    (1000) 
#define LM75A_TEMP_SHIFT   (5)    
 
#define TMP1075_OS_RES     (625)   
#define TMP1075_OS_MULT    (10000) 
#define TMP1075_OS_SHIFT   (4)     
#define TMP1075_TEMP_RES   (625)   
#define TMP1075_TEMP_MULT  (10000) 
#define TMP1075_TEMP_SHIFT (4)     
 
#if IS_ACTIVE(CONFIG_TMP1075_CONV_RATE_REG_27H)
#  define CONFIG_TMP1075_CONV_RATE_REG TMP1075_CONV_RATE_REG_27H
#  define TMP1075_CONV_RATE            (28)
#elif IS_ACTIVE(CONFIG_TMP1075_CONV_RATE_REG_55)
#  define CONFIG_TMP1075_CONV_RATE_REG TMP1075_CONV_RATE_REG_55
#  define TMP1075_CONV_RATE            (55)
#elif IS_ACTIVE(CONFIG_TMP1075_CONV_RATE_REG_110)
#  define CONFIG_TMP1075_CONV_RATE_REG TMP1075_CONV_RATE_REG_110
#  define TMP1075_CONV_RATE            (110)
#elif IS_ACTIVE(CONFIG_TMP1075_CONV_RATE_REG_220)
#  define CONFIG_TMP1075_CONV_RATE_REG TMP1075_CONV_RATE_REG_220
#  define TMP1075_CONV_RATE            (220)
#endif
 
#ifndef CONFIG_TMP1075_CONV_RATE_REG
#  define CONFIG_TMP1075_CONV_RATE_REG TMP1075_CONV_RATE_REG_27H
#  define TMP1075_CONV_RATE            (28)
#endif
 
#ifndef LM75_PARAMS
#  if IS_USED(MODULE_LM75A)
#    define LM75_PARAMS { .res = &lm75a_properties,               \
                          .gpio_alarm = LM75_PARAM_INT,           \
                          .conv_rate = LM75A_CONV_RATE,           \
                          .i2c_bus = LM75_PARAM_I2C,              \
                          .i2c_addr = CONFIG_LM75_I2C_ADDR,       \
                          .shutdown_mode = CONFIG_OPERATION_MODE, \
                          .tm_mode = CONFIG_THERMOSTAT_MODE,      \
                          .polarity = CONFIG_OS_POLARITY,         \
                          .fault_q = CONFIG_FAULT_QUEUE }
 
#  endif
 
#  if IS_USED(MODULE_TMP1075)
#    define LM75_PARAMS { .res = &tmp1075_properties,             \
                          .gpio_alarm = LM75_PARAM_INT,           \
                          .conv_rate = TMP1075_CONV_RATE,         \
                          .i2c_bus = LM75_PARAM_I2C,              \
                          .i2c_addr = CONFIG_LM75_I2C_ADDR,       \
                          .shutdown_mode = CONFIG_OPERATION_MODE, \
                          .tm_mode = CONFIG_THERMOSTAT_MODE,      \
                          .polarity = CONFIG_OS_POLARITY,         \
                          .fault_q = CONFIG_FAULT_QUEUE,          \
                          .conv_rate_reg = CONFIG_TMP1075_CONV_RATE_REG }
#  endif
#endif /* LM75_PARAMS */

static const lm75_params_t lm75_params[] = {
    LM75_PARAMS
};
 
#ifdef __cplusplus
}
#endif