81#include "net/ieee802154/radio.h"
91#define MRF24J40_PSEUDO_STATE_IDLE (0x01)
92#define MRF24J40_PSEUDO_STATE_SLEEP (0x02)
93#define MRF24J40_PSEUDO_STATE_RESET (0x04)
104#define MRF24J40_OPT_CSMA (0x0100)
105#define MRF24J40_OPT_PROMISCUOUS (0x0200)
107#define MRF24J40_OPT_PRELOADING (0x0400)
110#define MRF24J40_TASK_TX_DONE (0x01)
111#define MRF24J40_TASK_TX_READY (0x02)
112#define MRF24J40_TASK_RX_READY (0x04)
114#define MRF24J40_MAX_FRAME_RETRIES (3U)
116#define MRF24J40_MAX_MINBE (3U)
118#define MRF24J40_MIN_TXPOWER (-36)
119#define MRF24J40_MAX_TXPOWER (0)
136#define CONFIG_MRF24J40_USE_EXT_PA_LNA
148#define CONFIG_MRF24J40_TEST_SPI_CONNECTION
Definitions for netdev common IEEE 802.15.4 code.
Definitions low-level network driver interface.
Low-level GPIO peripheral driver interface definitions.
void mrf24j40_set_option(mrf24j40_t *dev, uint16_t option, bool state)
Enable or disable driver specific options.
void mrf24j40_set_csma_max_retries(mrf24j40_t *dev, int8_t retries)
Set the maximum number of channel access attempts per frame (CSMA)
int mrf24j40_init(mrf24j40_t *dev, const mrf24j40_params_t *params, ieee802154_dev_t *hal, gpio_cb_t cb, void *ctx)
Initialize the given MRF24J40 device.
void mrf24j40_sleep(mrf24j40_t *dev)
Put in sleep mode.
uint16_t mrf24j40_get_pan(mrf24j40_t *dev)
Get the configured PAN ID of the given device.
void mrf24j40_set_txpower(mrf24j40_t *dev, int16_t txpower)
Set the transmission power of the given device [in dBm].
void mrf24j40_set_addr_long(mrf24j40_t *dev, const uint8_t *addr)
Set the long address of the given device.
void mrf24j40_set_csma_backoff_exp(mrf24j40_t *dev, uint8_t min, uint8_t max)
Set the min and max backoff exponent for CSMA/CA.
uint8_t mrf24j40_get_chan(mrf24j40_t *dev)
Get the configured channel number of the given device.
int8_t mrf24j40_dbm_from_reg(uint8_t value)
Convert scalar from mrf24j40 RSSI to dBm.
void mrf24j40_tx_prepare(mrf24j40_t *dev)
Prepare for sending of data.
size_t mrf24j40_tx_load(mrf24j40_t *dev, uint8_t *data, size_t len, size_t offset)
Load chunks of data into the transmit buffer of the given device.
void mrf24j40_set_cca_threshold(mrf24j40_t *dev, int8_t value)
Set the CCA threshold value.
struct mrf24j40_params mrf24j40_params_t
struct holding all params needed for device initialization
void mrf24j40_radio_irq_handler(void *dev)
IRQ Handler for the MRF24J40 device.
void mrf24j40_software_reset(mrf24j40_t *dev)
Software Reset.
void mrf24j40_reset_state_machine(mrf24j40_t *dev)
Reset the internal state machine to TRX_OFF mode.
int mrf24j40_reset(mrf24j40_t *dev)
Trigger a hardware reset and configure radio with default values.
void mrf24j40_tx_exec(mrf24j40_t *dev)
Trigger sending of data previously loaded into transmit buffer.
void mrf24j40_set_state(mrf24j40_t *dev, uint8_t state)
Set the state of the given device (trigger a state change)
void mrf24j40_set_pan(mrf24j40_t *dev, uint16_t pan)
Set the PAN ID of the given device.
void mrf24j40_wake_up(mrf24j40_t *dev)
Wake up from sleep mode.
void mrf24j40_set_turbo(mrf24j40_t *dev, bool enable)
Enable or disable proprietary Turbo Mode.
void mrf24j40_set_chan(mrf24j40_t *dev, uint8_t chan)
Set the channel number of the given device.
void mrf24j40_set_addr_short(mrf24j40_t *dev, uint16_t addr)
Set the short address of the given device.
void(* gpio_cb_t)(void *arg)
Signature of event callback functions triggered from interrupts.
gpio_t spi_cs_t
Chip select pin type overlaps with gpio_t so it can be casted to this.
Protocol type definitions.
Low-level SPI peripheral driver interface definition.
the IEEE802.15.4 device descriptor
struct holding all params needed for device initialization
spi_t spi
SPI bus the device is connected to.
spi_cs_t cs_pin
GPIO pin connected to chip select.
spi_clk_t spi_clk
SPI speed to use.
gpio_t int_pin
GPIO pin connected to the interrupt pin.
gpio_t reset_pin
GPIO pin connected to the reset pin.
Device descriptor for MRF24J40 radio devices.
const mrf24j40_params_t * params
parameters for initialization
bool tx_pending
Whether a transmission is pending or not.
uint8_t fcf_low
Low 8 FCF bits of the current TX frame.
uint8_t pending
Flags for pending tasks.